stooge6

go to an arts and crafts store and get kneadable clay. it wont harden (set). i do not remember the exact name but you can find it in the sculpting section. the more you work this clay ,or get it warm, the softer it gets. use this to sculpt out your toy. you can reuse this stuff over and over. i also used lego's to make the frame for my molds then using hot glue to seal them to a cookie baking sheet. i got a little creative at work when i was creating molds for some of stuff we used to produce.

look up permaflex silicon. they make several different grades of silicon that u can use with varying levels of rigidity.

I have ALOT of experience with smooth-on. I used to work with it for my job. I used it to make molds for resin casting. Whenever I made a mold, I would try to mix a little extra so that i could make some toys. One of my favorites is a bowling pin (actual size) that I cast from a plastic bowling game. I still use that bowling pin as a plug quite often. I think I posted a guide for mixing and casting smooth on somewhere on here. found the post:

THANKS ARSE!! that is definitely going in my shopping cart.

Anyone know what toy this is? https://bigholestube.com/elbow-deep-ruber-fist-in-hotkinkyjo-anal-hole-belly-bulge-prolapse/

they lost me quite a while ago. i am not into pissing vids, almost every vid they have done for several years now has the girls getting pissed on and/or holding a glass that the men are pissing in and then being drank. i know some people enjoy this, thats fine. i'm not knocking it or poking fun at it, everyone is different, its just not in my wheel house of being erotic.

for those trying to keep their machines stable when "digging the hole", i did 2 things to stabilize my hismith. the first was i found a t-post for a small diameter fence post that was the diameter of the upright bars (about 1" diameter). it had set screws in the sides that would hold the t connection to the upright and the leg in place. i went to the hardware store and bought a 3' x 1" pipe that was threaded on both end with end caps on both ends. i filled the pip with sand and capped it off to give it a little weight. this gave it a wider leg base that stopped it from tipping over. the second was i purchased 2 sets of 10 pound leg weights. i put 1 weight on each leg, both sides front and back and there is very minimal sliding side to side. i hope this helps some of you with stabilizing the machine.

i was looking for a new sex machine this afternoon, something with at least 8+" thrust length when i came across this inflatable dildo... it looks FUN. i will probably get one in the near future, to expand my horizons amongst others holes. https://www.etsy.com/listing/1309094207/monster-dildo-xxl-inflatable-butt-plug?ga_order=most_relevant&ga_search_type=all&ga_view_type=gallery&ga_search_query=thrusting+machine&ref=sr_gallery-9-29&pro=1&frs=1&organic_search_click=1

i enjoy deep play, i regularly enjoy my 19" snake on my machine. i use exclusively a shower enema system now. my sigmoid is pretty much straightened out now and i work it in deep. it takes me a few tries to get the water to go past the bend. once it is past the bend i fill up in steps. i can feel the water going past the bend plus another sign is the water flowing out of my hole is greatly decreased. i will do this several times, each time cleaning deeper. the first pass is usually only about 20-30 secs. each time there is more room cleaned out so i can do successive fills lasting about 30-40 secs longer than before. when i get to the end i am usually about 2-3 mins in total. but i am always sensitive to any pain/discomfort while filling up. if i have any pain i stop immediately. sometimes i can hold it in for a few and others it wants drained out now. my hole starts making mucus while i am cleaning and i know i am done when the mucus is mostly clear. the only problem i usually have is there is usually some left over water that takes about 30 mins to decend so it can be expelled. if this is clear, i do one last flushing of the lower sphincter to eliminate any last residue. hope this helps.

i find that after a session of pushing my limits with either width or depth if i take a full week (or 2) off afterwards i can more readily take the same toy alot easier than before. when i was going through physical therapy for my broken knee, the therapist taught me to work my muscles (leg) hard but take breaks after and the next session would be smoother and easier. i think the same applies to my anal workouts.

i think its all the above. the more u play the more u work the muscles. although recently last weekend. i was able to take the next upsize (3" dia) toy i have deeper than before, lots deeper, almost the whole 14 inches deep. lots of exercise.....

one thing i forgot, several sites that i found info on working depth said to lay on your right side. i did this and i think it helped some. i thought of my stretching discomfort as being comparable to doing a workout and having some muscle ache afterwards. as for the discomfort from pusging my depths, i didnt go totally 18" deep in one shot. it took me several sessions working and going about 1-2" deeper each session. sometimes i gained nothing but i did exercise the previous depths i had achieved. i never did it but i read that using aspercreme mixed with your lube can help some for minor numbing. numbing isnt the best thing to do, pain is a good sign you may need to stop. the first time i got it to were i had over 17" of my db ender inside my hole, i barely stroked myself 5 times before i shot a big load high up onto my chest.

i used an 18" x1.5" double ender until i straightened my sigmoid. then i widened it with the Exxtreme dildo (16" x 2.25) from amazon. after that i stepped up to the rambone dildo or the med goose until both were completely up my hole. after the rambone i could handle both an 18" anal snake and the db ender full length at the same time. i am currently working on the lg goose.

i bought a toy bowling set from walmart that is about 2/3 of the size of a real bowling pin. they are a little over 9" diameter. they are hollow and just hard enough to use as a butt plug. i slip a condom over the fat end to keep anything from going into the hole on the bottom. lube it up and it is a pleasurable plug to slide in for extended wear or to rub one off. also i used to work with liquid silicon molding, very similar grade and material to silicon dildo material. i took another toy bowling pin from a different set, actual size, and cast a silicon bowling pin that is also enjoyable as a plug. both bowling pin sets were available at walmart. i bought the quite a few years ago and enjoy them still.

i too have a hismith. i will eventually get a kong but for now i am enjoying my hismith and a couple of others have enjoyed being "stuck" on the recieving end of it. NZanalslut said "Interesting, I have a hismith one but put old paint buckets filled with water on the legs so that its stays in place at higher speeds. it ends up being able to fuck quite fast remaining stable". i had the same issue but i used 4 ankle weights each weighing 10 pounds to stabilize mine. fold them in half and put 2 each on front n back legs. i have no problem with my xl rentman.